Type to search

Kodak EasyShare Printer Dock Series3 Setup Guide [Step-by-Step]

In the global market, Kodak is one of the most famous printer manufacturing brands. Many users prefer this Kodak printer for its high-end feature. So, if you are a new user of the Kodak EasyShare Printer Dock Series3, then you might need to know its complete setup process right at the beginning. In that case, you can go ahead this post, as here in this post, you will get the Kodak EasyShare Printer Dock Series3 Setup guidance with the complete steps. Hence, stay on this page and perform the setup of the Kodak EasyShare Printer Dock Series3.

 

Kodak EasyShare Printer Dock Series3 Setup with just a Few Clicks

Here, in this section of the article, we have mentioned the complete setup process of the Kodak EasyShare printer dock series3. So, let us begin:

 

Find a Location for your Printer Dock

Firstly, you need to find a location for the Kodak EasyShare printer dock. In that case, you need to place the Kodak printer into a clean, flat, ad dust-free surface. Then, from the back of the printer dock, allow at least 5 in. (12.7cm) for the paper travel. Now, you need to be sure that the top and back of the printer dock are not blocked for the proper ventilation. Next, you keep the cable clear of the paper path to the front and rear area of the printer dock while connecting the power or USB cables. Keep in mind, you have to avoid those areas where open doors, ventilation ducts, or frequent passersby might expose the printer dock and paper to high levels of debris and dust. Apart from these, the Airborne dirt molecule can influence picture quality.

 

Install the Custom Camera Insert

Now, it’s time to install the custom camera insert. Therefore, it is necessary to use the custom which came up with your digital camera in order to dock the camera. In case if you use any other custom, then the camera might not fit properly into the printer dock. You may also need to use the Kodak dock adapter D-26, as it depends on your camera connector. So, you need to follow the guidelines included with the dock adapter. Now, simply remove the outer packing material that is covering the connector. After that, toward the back of the printer dock, place the rear tabs of the insert in the slots. Now, press the front of the insert down and snap into the proper place.

 

Connect the Power

After that, you need to connect the power. Thus, you have to remove the camera from the docks first. Then, attach the AC power cord to the AC power adapter and now, the other end is to be connected to the back of the printer dock. Once you are done, connect the AC power cord to the power outlet.

 

Note: As the risk of electric shock, only use AC power adapter included with your Kodak printer dock. Other cords or adapters can damage the printer dock, camera or computer.

 

Handle and Store the color cartridge

Now, you have to store the color cartridges in a location where the temperature doesn’t exist 30  °C or 85 °F for best quality prints. Moreover, you can handle the color cartridge by the spool ends in order to avoid getting fingerprints on the ribbon. Apart from these, always keep the cartridge away from the out of high-temperature environments or direct sunlight.

 

Install and Remove the Color Cartridge

Now, you need to install and remove the color cartridges. To do so, primarily, you need to open the cartridge door and then, check to be sure that there is no slack in the color cartridge ribbon. Now, push the cartridge spool in order to remove the slack and then rotate the spool clockwise. After that, with the arrow pointing toward the printer dock, slide the color cartridge in, label side up. Until it “clicks” into place, keep pushing the cartridge. When it is done, simply close the cartridge door.

 

Note- Be aware to rotate the spool more than essential. Furthermore, if there is a paper error, the color cartridge might lock in place. I such times, you have to clear the p[er error first and after that, try to remove the cartridge. Also, before attempting the cartridge, ensure the paper light is off.

Now, in order to remove the ink cartridge, you need to open the cartridge box and then, push up on the green lever. After that, slide the cartridge out carefully. When the cartridge is nearly empty, the ink cartridge light continuously blinks. Moreover, sometimes, you might see, when the ink cartridge is depleted, the cartridge light glows amber. Once the new cartridge installation process is over, you can press the Print button in order to clear the cartridge and re-use the printing.

Hold and Store the Paper

In the next step, you need to hold and store the paper. In such situations, you need to be aware of some basic things such as:

  • Handle the paper by the perforated or by the edges, in order to avoid fingerprints. Don’t touch the reflecting side.
  • Remove the paper tray, when storing and then, close the paper tray cover and paper tray door in order to keep out debris and dust. And, store paper flat.
  • Apart from this, you need to keep the paper away out of the high-temperature environments such as a vehicle parked in the sun. Keep it away from the direct sunlight.

Load the Paper

Now, it’s time to load the paper. While performing the task, at first, you need to remove the paper tray from the printer dock. After that, slide the paper tray cover back, until it ‘Press’ into the place, about 1.25 in. (3 cm). Now, you have to uphold on the end of the paper tray cover. Next, in order to keep the sheet from sticking together, carefully, ‘Fan’ the paper. Now, with the Kodak logo side facing down, load the paper into the paper tray. Once it is done, simply close the paper tray cover.

 

Note: In order to prevent overloading, don’t load more than 25 sheets of paper. Moreover, don’t touch the glossy side of the paper to avoid fingerprints. Furthermore, don’t load the paper which is missing perforated tabs.

 

Install and Remove the Paper Tray

After loading the paper, you require installing and remove the paper tray. To so so follow the below instructions:

  • First, on the Kodak printer dock, open the paper dock.
  • Then, slide the paper cover, until is click in the proper place, about 1.25 in. (3 cm)
  • After that, you need to make sure the paper tray fits squarely on the printer dock. Moreover, while installing, you have to ensure to keep the paper tray cover all the way open.
  • Now, you need to pull the paper out in order to remove it.
  • Then, close the paper tray cover ad paper tray door in order to keep out debris and dust.

Therefore, when the paper light glows steady, you can understand that the paper tray is empty. Therefore, you need to refill and reinstall the paper tray again. Once you are done, you need to press the ‘Print’ button. In this way, you can clear the paper error and resume printing,

 

Install the Software

After setting up the Kodak EasyShare printer dock series3, you might need to know the software installation process. To do that, your system needs minimum requirements, such as:

 

Macintosh Computers:

  • Power Mac G3, G4, G5, G4 Cube, iMac; PowerBook G3, G4, or iBook computers.
  • 128 MB RAM
  • CD-ROM drive
  • Mac OS 10.2 or higher
  • 200 MB hard disk space available
  • USB port available
  • Safari 1.0 or higher for complete installation
  • Color monitor, 1024 x 768 pixels

Windows Operating System Based Computers:

  • Windows 98, 98SE, ME, 2000 SP1, or XP OS
  • 233 MHz processor or greater
  • CD-ROM drive
  • 64 MB RAM ( for Windows XP OS 128 MB RAM)
  • Available USB port
  • Internet Explorer 5.01 or higher
  • Color monitor, 800 x 600 pixels (24-bit or 16-bit recommended)

Installing Process of the Software

Note: Before connecting to the printer dock to the computer,install the Kodak EasyShare software.

enter:

In order to install the software, primarily, you need to close all the active program including the antivirus software. After that, into the CD-ROM drive, place the Kodak EasyShare software CD. Then, load the software:

For Windows OS Based Computer– Select the ‘Start Menu’ and then, enter :  d:\setup.exe where‘d’ is the drive letter which contains the CD.

For Mac OS X– At first, double-tap on the CD icon, Then, hit the ‘Install’ option.

Now, you need to follow the on-screen guidelines in order to install the software.

  • Choose Complete to automatically install the most commonly used apps, select Custom in order to choose the software that you require installing.

 

Important Note: If you use the printer dock with a computer, then you have to install the printer driver. And if you select Custom, then ensure that the printer docked is selected. Moreover, if you choose Typical, then the printer driver is automatically installed.

 

Adding the Printer for your Mac OS X

  1. Primarily, you have to navigate to the finder window and then tap on the Application option. However, if you don’t find the Application button, then you have to open the Application folder on your operating drive.
  2. After that, you have to go to the Utilities folder and double-tap on the Print Center.
  3. Now, navigate to the printer list window and press the Add Printer option.
  4. Next, choose the printer dock and hit the Add button. Now, the printer dock is added to your computer.
  5. After that, you’ll be prompted to Restart your device. If you disable your security software, then Enable it and see the antivirus software manual for more details.

For more details on installing the software, you can see the ReadMe file that is on the Kodak EasyShare CD. If you want to know more about the software applications included on the Kodak EasyShare software CD, tap on the Help option that is in the EasyShare software.

 

Uninstalling the Software

If you want to remove the EasyShare software or printer driver from your computer, then you have to proceed to the following procedure:

 

Windows OS Based Computer:

  • Firstly, go to the Start menu and then, select the Settings. Now, navigate to the Control Panel.
  • Then, double-tap on the ‘dd/Remove option.
  • After that, click on the Kodak EasyShare software, and then, it the Remove key.
  • Once it Is done, you have to uninstall the single components, such as the printer driver. Therefore, choose the Modify button.
  • Now, follow the on-screen guideline in order to complete the further procedure. And lastly, restart your device if prompted.

Mac OS X:

  • First of all, double-click the operating for your device.
  • Then, choose the Library option.
  • After that, tap on the Printers.
  • Now, go to the Kodak folder and ten, open the printer dock folder.
  • Next, you to double-click on the printer dock uninstaller program.
  • Finally, follow the on-screen instructions to finish the procedure.

Ending Notes

We hope that after learning the complete setup process, you can perform the Kodak EasyShare printer dock series3 Setup without facing any issue. However, if you have any doubts regarding the Kodak EasyShare printer dock series3 Setup, then you can feed in your doubts in the feedback section below. On the other hand, you can also take expert assistance for instant help.

WordPress › Error

There has been a critical error on this website.

Learn more about troubleshooting WordPress.